Analysis of the behavior of asynchronous electric drive with a closed scalar control system when changing the inductance of the magnetizing circuit

Yu. L. Zhukovskiy, B. Y. Vasilev, N. A. Korolev, Y. M. Malkova

Abstract


The article was devoted to the study of an automated electric drive with a scalar closed-loop speed control system. Severe duty and operating modes of electric drive determine the actual service life. Wear of the induction motor, as a key link of the electric drive, was associated with deviation from nominal parameters. The deviation of parameters of the induction motor equivalent circuit determined the resultant change of characteristics. The parameters of the equivalent circuit determined the accuracy of the adjustment of regulators and optimal algorithms in the control system of the electric drive. In continuous operation modes the possibility of auto-tuning regulators, which requires stopping or no-load mode, was excluded. The paper considered the influence of the magnetization circuit mutual inductance value of the induction motor on the behavior of the electric drive control system. Evaluation of the behavior of the scalar closed-loop speed control system was performed on the basic energy (power factor, efficiency factor) and mechanical (speed, electromagnetic torque) characteristics of the electric drive.

Keywords


Automatic electric drive; Induction motor; Parameters of equivalent circuit; Magnetization circuit mutual inductance; Scalar control system; Technical condition

Full Text:

PDF

References


Bento, F., Adouni, A., Muxiri, A. C., Fonseca, D. S., and Marques Cardoso, A. J. (2021). On the risk of failure to prevent induction motors permanent damage, due to the short available time‐to‐diagnosis of inter‐turn short‐circuit faults. IET Electric Power Applications, 15(1), 51-62.

Boikov, A., and Payor, V. (2022). The present issues of control automation for levitation metal melting. Symmetry, 14(10), 1968.

Bolobov, V. I., Chupin, S. A., Bochkov, V. S., and Mishin, I. I. (2019). Service life extension for rock cutters by increasing wear resistance of holders by thermomechanical treatment. Journal of Mining Institute, 5, 67-71.

Dokka, Z., Liubov, N., and Filatova, I. (2020). Problems of oil refining industry development in Russia. International Journal of Engineering Research and Technology, 13(2), 267-270.

Emelianov, A. P., and Churkin, B. A. (2014). Scalar control of squirrel-cage induction motor with stator active current. Bulletin of the South Ural State University, Series" Power Engineering, 14(3), 85-90.

Ewert, P., Kowalski, C. T., and Orlowska-Kowalska, T. (2020). Low-cost monitoring and diagnosis system for rolling bearing faults of the induction motor based on neural network approach. Electronics, 9(9), 1334.

Fernandez-Cavero, V., García-Escudero, L. A., Pons-Llinares, J., Fernández-Temprano, M. A., Duque-Perez, O., and Morinigo-Sotelo, D. (2021). Diagnosis of broken rotor bars during the startup of inverter-fed induction motors using the dragon transform and functional ANOVA. Applied Sciences, 11(9), 3769.

Garcia-Calva, T. A., Morinigo-Sotelo, D., Fernandez-Cavero, V., Garcia-Perez, A., and Romero-Troncoso, R. D. J. (2021). Early detection of broken rotor bars in inverter-fed induction motors using speed analysis of startup transients. Energies, 14(5), 1469.

Graciola, C. L., Goedtel, A., Angélico, B. A., Castoldi, M. F., and Costa, B. L. G. (2022). Energy efficiency optimization strategy for scalar control of three-phase induction motors. Journal of Control, Automation and Electrical Systems, 33(3), 1032-1043.

Gridin, V. M. (2012). Calculation of parameters of the asynchronous motor equivalent circuit according to catalogue data. Electricity, 5, 40-44.

Hua, B., Zhengming, Z., Shuo, M., Jianzheng, L., and Xiaoying, S. (2003). Comparison of three PWM strategies-SPWM, SVPWM and one-cycle control. The Fifth International Conference on Power Electronics and Drive Systems, 2003. PEDS 2003, 2, 1313-1316.

Jabłoński, M., and Borkowski, P. (2022). Correction mechanism for balancing driving torques in an opencast mining stacker with an induction motor and converter drive system. Energies, 15(4), 1282.

Klyuev, R. V., Golik, V. I., Bosikov, I. I., and Gavrina, O. A. (2021). Analysis of electric power loss in the power supply system of the concentrating factory. Bulletin of the Tomsk Polytechnic University. Geo Assets Engineering, 332(10), 7-16.

Koteleva, N. I., Korolev, N. A., and Zhukovskiy, Y. L. (2021). Identification of the technical condition of induction motor groups by the total energy flow. Energies, 14(20), 6677.

Krishnasamy, B., and Ashok, K. (2022). Assessment of harmonic mitigation in v/f drive of induction motor using an ann-based hybrid power filter for a wheat flour mill. Processes, 10(6), 1191.

Kudelina, K., Vaimann, T., Asad, B., Rassõlkin, A., Kallaste, A., and Demidova, G. (2021). Trends and challenges in intelligent condition monitoring of electrical machines using machine learning. Applied Sciences, 11(6), 2761.

Lavrenko, S. A., and Shishlyannikov, D. I. (2021). Performance evaluation of heading-and-winning machines in the conditions of potash mines. Applied Sciences, 11(8), 3444.

Manikandan, S., and Duraivelu, K. (2021). Fault diagnosis of various rotating equipment using machine learning approaches–A review. Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, 235(2), 629-642.

Marfoli, A., Di Nardo, M., Degano, M., Gerada, C., and Jara, W. (2021). Squirrel cage induction motor: A design-based comparison between aluminium and copper cages. IEEE Open Journal of Industry Applications, 2, 110-120.

Nikolaev, A. V., Vöth, S., and Kychkin, A. V. (2022). Application of the cybernetic approach to price-dependent demand response for underground mining enterprise electricity consumption. Journal of Mining Institute, 000, 1-10.

Ostroverkhov, V. V., and Nalivaiko, N. V. (2020). Condition assessment and diagnostics of asynchronous electric motors using signature analysis of consumed current. Russian Electrical Engineering, 91(11), 714-723.

Pedra, J. (2008). On the determination of induction motor parameters from manufacturer data for electromagnetic transient programs. IEEE Transactions on Power Systems, 23(4), 1709-1718.

Pietrzak, P., and Wolkiewicz, M. (2021). On-line detection and classification of PMSM stator winding faults based on stator current symmetrical components analysis and the KNN algorithm. Electronics, 10(15), 1786.

Runji, J. M., Lee, Y. J., and Chu, C. H. (2022). User requirements analysis on augmented reality-based maintenance in manufacturing. Journal of Computing and Information Science in Engineering, 22(5), 050901.

Savard, C., Iakovleva, E., Ivanchenko, D., and Rassõlkin, A. (2021). Accessible battery model with aging dependency. Energies, 14(12), 3493.

Skamyin, A., Shklyarskiy, Y., Dobush, I., Dobush, V., Sutikno, T., and Jopri, M. H. (2022). An assessment of the share contributions of distortion sources for various load parameters. International Journal of Power Electronics and Drive Systems, 13(2), 950-959.

Sultana, B., Scicluna, K., Attard, J., Seguna, C., and Scerri, J. (2021). Design of a FPGA-based inverter drive for hf injection based sensorless control. 2021 22nd IEEE International Conference on Industrial Technology (ICIT), 1, 178-183.

Sun, X. D., Koh, K. H., Yu, B. G., and Matsui, M. (2009). Fuzzy-logic-based V/f control of an induction motor for a DC grid power-leveling system using flywheel energy storage equipment. IEEE Transactions on Industrial Electronics, 56(8), 3161-3168.

Sychev, Y. A., Aladin M. E., and Serikov, V. A. (2022). Developing a hybrid filter structure and a control algorithm for hybrid power supply. International Journal of Power Electronics and Drive Systems, 13(2), 1625-1634.

Ustun, S. V., and Demirtas, M. (2009). Modeling and control of V/f controlled induction motor using genetic-ANFIS algorithm. Energy Conversion and Management, 50(3), 786-791.

Vasilev, B. (2019). Analysis and improvement of the efficiency of frequency converters with pulse width modulation. International Journal of Electrical and Computer Engineering, 9(4), 2314.

Vasilyeva, N. V., Boikov, A. V., Erokhina, О. О., and Trifonov, A. Y. (2021) Automated digitization of radial charts. Journal of Mining Institute , 247, 82-87.

Voronin, V. A., and Nepsha, F. S. (2020). Simulation of the electric drive of the shearer to assess the energy efficiency indicators of the power supply system. Journal of Mining Institute, 246, 633-639.

Xiao, L., Xu, Y., Sun, X., Xu, H., and Zhang, L. (2022). Experimental investigation on the effect of misalignment on the wear failure for spline couplings. Engineering Failure Analysis, 131, 105755.

Zhang, W. F., and Yu, Y. H. (2007). Comparison of three SVPWM strategies. Journal of Electronic Science and Technology, 5(3), 283-287.

Zhou, X., Mao, S., and Li, M. (2021). A novel anti-noise fault diagnosis approach for rolling bearings based on convolutional neural network fusing frequency domain feature matching algorithm. Sensors, 21(16), 5532.




DOI: https://doi.org/10.17509/ijost.v8i1.51983

Refbacks

  • There are currently no refbacks.


Copyright (c) 2022 Universitas Pendidikan Indonesia

Creative Commons License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

Indonesian Journal of Science and Technology is published by UPI.
StatCounter - Free Web Tracker and Counter
View My Stats