Microstructure and Wear Behavior of Repair Weld on the Flash-Butt Welded Rail

Hein Zaw Oo, Prapas Muangjunburee

Abstract


This study aimed to evaluate the potential of using a standard arc welding process to repair surface defects in flash-butt welded (FBW) rails by examining their microstructural, mechanical, and tribological properties. Macrostructural analysis, optical microscopy (OM), field emission scanning electron microscopy (FESEM), hardness testing, and wear tests were employed to compare original and repaired FBWs. The repaired weld revealed fine pearlite in the heat-affected zone (HAZ) and acicular ferrite in the weld metal, while hardness results indicated a higher and more uniform distribution across the weld metal and HAZ than in the original FBW. Wear tests showed that both welds had similar coefficients of friction and wear track widths, but the repaired FBW demonstrated less weight loss. SEM analysis identified micro-ploughing and micro-cutting as dominant wear mechanisms in the original FBW, whereas the repaired FBW primarily exhibited micro-ploughing and oxide delamination. These findings indicate that arc welding repair not only improves hardness uniformity but also enhances wear resistance without significantly affecting frictional behavior. In conclusion, the arc welding process can be considered an effective method for restoring the surface integrity of FBW rails, with the implication that its application in rail maintenance may extend rail service life and reduce replacement costs.

Keywords


Flash-butt Rail Welding; Hardness; Rail Steel; Repair Welding; Wear

Full Text:

PDF

References


Skyttebol, A., Josefson, B. L., and Ringsberg, J. W. (2005). Fatigue crack growth in a welded rail under the influence of residual stresses. Engineering Fracture Mechanics, 72(2), 271–285.

Lim, N.-H., Park, N.-H., and Kang, Y.-J. (2003). Stability of continuous welded rail track. Computers and Structures, 81(22–23), 2219–2236.

Shen, M., Mei, L., Gong, F., Li, C., and Li, Q. (2024). Damage behaviour of rail flash-butt welding joints under controlled impact kinetic energy. Wear, 552–553, 205435.

Jiang, W. J., Liu, C., He, C. G., Guo, J., Wang, W. J., and Liu, Q. Y. (2017). Investigation on impact wear and damage mechanism of railway rail weld joint and rail materials. Wear, 376–377, 1938–1946.

Burapa, R., Oo, H. Z., Sangwiman, W., and Muangjunburee, P. (2024). Influences of preheating parameters on the quality of weld by thermite rail welding. Materials Research Express, 11(6), 066507.

Wang, J., Ma, C., Han, J., Jiang, Z., and Linton, V. (2021). Acquisition of HSLA steel weld joints with excellent mechanical performance through flash butt welding physical simulation. Materials Letters, 303, 130511.

Ozakgul, K., Piroglu, F., and Caglayan, O. (2015). An experimental investigation on flash butt welded rails. Engineering Failure Analysis, 57, 21–30.

Xiao, G., Xiao, X., Guo, J., Wen, Z., and Jin, X. (2010). Track dynamic behavior at rail welds at high speed. Acta Mechanica Sinica, 26(3), 449–465.

Wu, Y., Lun Pun, C., Su, H., Huang, P., Welsby, D., Mutton, P., and Yan, W. (2022). Numerical study on ratcheting performance of heavy haul rail flash-butt welds in curved tracks. Engineering Failure Analysis, 140, 106611.

Bauri, L. F., Alves, L. H. D., Pereira, H. B., Tschiptschin, A. P., and Goldenstein, H. (2020). The role of welding parameters on the control of the microstructure and mechanical properties of rails welded using FBW. Journal of Materials Research and Technology, 9(4), 8058–8073.

Mansouri, H., and Monshi, A. (2004). Microstructure and residual stress variations in weld zone of flash-butt welded railroads. Science and Technology of Welding and Joining, 9(3), 237–245.

Tawfik, D., Mutton, P. J., and Chiu, W. K. (2008). Experimental and numerical investigations: Alleviating tensile residual stresses in flash-butt welds by localised rapid post-weld heat treatment. Journal of Materials Processing Technology, 196(1–3), 279–291.

Shi, H. C., Shi, L. B., Ding, H. H., Wang, W. J., Jiang, W. J., Guo, J., and Liu, Q. Y. (2019). Influence of laser strengthening techniques on anti-wear and anti-fatigue properties of rail welding joint. Engineering Failure Analysis, 101, 72–85.

Su, H., Li, J., Lai, Q., Pun, C. L., Mutton, P., Kan, Q., Kang, G., and Yan, W. (2020). Ratcheting behaviour of flash butt welds in heat-treated hypereutectoid steel rails under uniaxial and biaxial cyclic loadings. International Journal of Mechanical Sciences, 176, 105539.

Lu, C., Nieto, J., Puy, I., Melendez, J., and Martínez-Esnaola, J. M. (2018). Fatigue prediction of rail welded joints. International Journal of Fatigue, 113, 78–87.

Wang, Y., Zhou, H., Shi, Y., and Feng, B. (2012). Mechanical properties and fracture toughness of rail steels and thermite welds at low temperature. International Journal of Minerals, Metallurgy, and Materials, 19(5), 409–420.

Losz, J. M. B., Saboury, S., and McNutt, T. M. (1995). Microstructural characterization of submerged-arc and gas-metal-arc weldments in HY-130 Steel. ISIJ International, 35(1), 71–78.

Pereira, H. B., Echeverri, E. A. A., Alves, L. H. D., and Goldenstein, H. (2022). Evaluation of the effect of heat input and cooling rate of rail flash-butt welding using finite element method simulation. Soldagem and Inspeção, 27, e2701.

Nishikawa, L. P., and Goldenstein, H. (2019). Divorced eutectoid on heat-affected zone of welded pearlitic rails. JOM, 71(2), 815–823.

Pavlina, E. J., and Van Tyne, C. J. (2008). Correlation of yield strength and tensile strength with hardness for steels. Journal of Materials Engineering and Performance, 17(6), 888–893.

Porcaro, R. R., Faria, G. L., Godefroid, L. B., Apolonio, G. R., Cândido, L. C., and Pinto, E. S. (2019). Microstructure and mechanical properties of a flash butt welded pearlitic rail. Journal of Materials Processing Technology, 270, 20–27.

Steenbergen, M., and Dollevoet, R. (2013). On the mechanism of squat formation on train rails – Part II: Growth. International Journal of Fatigue, 47, 373–381.

Fegredo, D. M., Kalousek, J., and Shehata, M. T. (1993). The effect of progressive minor spheroidization on the dry-wear rates of a standard carbon and a Cr-Mo alloy rail steel. Wear, 161(1–2), 29–40.

Mutton, P., Cookson, J., Qiu, C., and Welsby, D. (2016). Microstructural characterisation of rolling contact fatigue damage in flashbutt welds. Wear, 366–367, 368–377.

Steenbergen, M. (2021). On the genesis of squat-type defects on rails–Toward a unified explanation. Wear, 478, 203906.

Oo, H. Z., and Muangjunburee, P. (2023). Improving microstructure and hardness of softening area at HAZ of thermite welding on rail running surface. Materials Today Communications, 34, 105485.

Oo, H. Z., and Muangjunburee, P. (2024). Hardfacing of thermite welded rail by flux-cored arc welding. Wear, 546, 205314.

Su, H., Pun, C. L., Mutton, P., Kan, Q., Kang, G., and Yan, W. (2021). Numerical study on the ratcheting performance of rail flash butt welds in heavy haul operations. International Journal of Mechanical Sciences, 199, 106434.

Abson, D. J., and Pargeter, R. J. (1986). Factors influencing as-deposited strength, microstructure, and toughness of manual metal arc welds suitable for C-Mn steel fabrications. International Metals Reviews, 31(1), 141–196.

Madariaga, I., Gutierrez, I., and Bhadeshia, H. K. D. H. (2001). Acicular ferrite morphologies in a medium-carbon microalloyed steel. Metallurgical and Materials Transactions A, 32(9), 2187–2197.

Loder, D., Michelic, S. K., and Bernhard, C. (2016). Acicular ferrite formation and its influencing factors-a review. Journal of Materials Science Research, 6(1), 24.

Muangjunburee, P., Oo, H. Z., Rahim, S. Z. A., and Srikarun, B. (2024). Effects of heat input and preheating temperature on the microstructure and hardness of repairing the heat-affected zone of thermite welded rail head surface. Indonesian Journal of Science and Technology, 9(2), 421–440.

Krolicka, A., Lesiuk, G., Radwański, K., Kuziak, R., Janik, A., Mech, R., and Zygmunt, T. (2021). Comparison of fatigue crack growth rate: Pearlitic rail versus bainitic rail. International Journal of Fatigue, 149, 106280.

Masoumi, M., Lima, N. B. de, Tressia, G., Sinatora, A., and Goldenstein, H. (2019). Microstructure and crystallographic orientation evolutions below the superficial white layer of a used pearlitic rail. Journal of Materials Research and Technology, 8(6), 6275–6288.

Fei, J., Zhou, G., Zhou, J., Zhou, X., Li, Z., Zuo, D., and Wu, R. (2023). Research on the effect of pearlite lamellar spacing on rolling contact wear behavior of U75V rail steel. Metals, 13(2), 237.

Krolicka, A., Radwański, K., Kuziak, R., Zygmunt, T., and Ambroziak, A. (2020). Microstructure-based approach to the evaluation of welded joints of bainitic rails designed for high-speed railways. Journal of Constructional Steel Research, 175, 106372.

Krolicka, A., Zak, A., Kuziak, R., Radwanski, K., and Ambroziak, A. (2021). Decomposition mechanisms of continuously cooled bainitic rail in the critical heat-Affected zone of a flash-butt welded joints. Materials Science- Poland, 39(4), 615–625.




DOI: https://doi.org/10.17509/ijost.v11i2.89691

Refbacks

  • There are currently no refbacks.


Copyright (c) 2025 Universitas Pendidikan Indonesia

Creative Commons License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

Indonesian Journal of Science and Technology is published by UPI.
StatCounter - Free Web Tracker and Counter
View My Stats